6 Best
Pump Pool Heaters
-
Product Highlights- [connect with circulation pump]: spa heater have to connected with circulation pump with power of more than 0.5hp. smaller pumps may not provide enough water flow to activate the heater. also, the spa thermostat has to be with a circulation pump rather than a booster pump or submersible pump.
- [tips for heating]: it's recommended to fill the hot tub with hot water instead of cold water, as cold water can impact the heating performance. additionally, it's advisable to limit the water capacity to no more than 400 us gallons and to use an insulation cover to retain the temperature. otherwise, it may take a long time or may not heat up at all.
- [constant temperature control]: use the temperature knob to set and maintain the desired water temperature from 0 to 45°c. once the desired temperature is set, the thermostat continuously monitors and adjusts the operation of the heating system to maintain the water at a constant temperature.
- [1.5" pvc plumbing]: mxmoonant hot tub heater is equipped with 1.5" pvc pipe fittings, so you should use sch 40 1.5" pvc pipe for the plumbing connection. a smaller size may result in insufficient water flow. if you want to use other pipe sizes, please note that everything should start with 1.5".
- [no plug]: the pool thermostat does not come with a plug as it is a high power device. it should be connected to a 20a gfci circuit breaker. it is recommended that you contact a professional electrician to complete the circuit connection.
SHOWview product -
Product Highlights
- A better way to extend your swim season: nothing beats a warm swimming pool for your kids, pets and the whole family! what you’ll need is a highly efficient, low operating cost heating system – an aychlg pool heat pump for your pool to extend the fun for a few more months!
- The product is easy to operate, provides a mechanical fit for thermostat switch, you can set the temperature of temperature technology
- Note：must work with at least 0.75hp circulating pump,water pressure more than 20kpa.need 24 hours for heating pool.suitable for pools up to 2000 gallons in coastal climates.the temperature ranged from 40 °f-122 °f (5 °c-50 °c).material: metal;voltage: 220-240v/50-60hz;power: 3kw;current: 14a;phase parameters: single phase;note:one interface is 50mm, the other port is 32...
- Superb energy saver:the pool heater is a heat pump specifically designed for swimming pools. the operation only requires very limited electric input, hence its high efficiency and heat conversion rate can reach a score of cop 84.2.
- The product is small, suitable for: hot tub & swimming pool equipment and it is easy to install in the bathtub at the bottom of the circulating massage pipe
SHOWview product -
Product Highlights
- Easy to control: the pool heater has a mechanically coordinated thermostat switch ,make it easy to operate and control. the intelligent control system can automatically start and stop according to the water temperature, saving energy, and can also adjust the water temperature to meet different needs.
- Compact design: small and compact appearance design, 13.39* 4.8* 4.92inch, the hot tub water heater is easy to install and use, especially suitable for hot tub and swimming pool equipment, making your swimming pool and spa jacuzzi more beautiful and tidy.
- Efficient heating: electric pool water heater,3kw power,14a current, suitable for 220v-240v work voltage. quickly heat swimming pools and spa massage pools up to 2m³（70cuft）, allowing you to enjoy warm water as soon as possible.
- Dry burning prevention: the swimming pool heater is equipped with a pressure switch,which can protect it from the risk of dry burning.so at least 0.75hp（500w）circulating pump is needed to meet the pressure requirement.when the water pressure is not enough, the power supply will be cut off and the thermostat stop heating.
- Suggestions: this is a mini pool heater, please pay attention to the water capacity of the equipment. water above 2.0 cubic meters will affect heating efficiency or not heated to the specified temperature. please read the attached product manual carefully before installation, and install it in accordance with the requirements.
SHOWview product -
Product Highlights
- Inlet size:1.97 inch ;outlet size:1.3 inch;wire: 3*4mm²;pipe diameter: 1inch;size: 13.39* 4.8* 4.92inch
- The product is easy to operate, provides a mechanical fit for thermostat switch, you can set the temperature of temperature technology
- Must work with at least 0.75hp circulating pump,water pressure more than 20kpa.need 24 hours for heating pool.material: metal;voltage: 220-240v/50-60hz;power: 3kw;current: 14a;phase parameters: single phase;note:one interface is 50mm, the other port is 32mm, please note the size of the pipe before use.
- Heating fit for thermostat liner material is 316 # stainless steel pipe and electric resistance,corrosion resistance (chlorine corrosion)，and durable
- The product is small, suitable for: hot tub & swimming pool equipment and it is easy to install in the bathtub at the bottom of the circulating massage pipe
SHOWview product -
Product Highlights
- Coasts thermostat operation is fully automated, clockwise, the heating is on, indicator light, temperature reaches a preset temperature, will remain at that temperature
- Automatic heating: thermostat will first reach the preset temperature, then stop working until the temperature dropped a few degrees, the thermostat automatically turns on
- The initial set temperature settings: coasts equipped with ultra-high temperature protection thermostat switch, use an accurate thermometer to measure the water temperature should be at 40 °c
- The thermostat can be maintained within a temperature not exceeding 40 °c (104 °f) range. if cold water is started, will be 6 ~ 8 °c / h elevated temperatures
- Ultra-high temperature (over 49 °c), ultra-high temperature switch will automatically trip (power off)
SHOWview product -
Coupon copied
