10 Best
Furnace Replacement Cords
-
Product Highlights- Rated voltage: ac 120v +/- 10%-15%.50/60hz; coldresistance:18-40 ohm (ω)； rated current at 17 sec: 1.1-1.2 amps, voltage:l120v-132v. you can measure whether the hot surface ignitor is working properly with a multimeter.
- Lift time of the silicone hot rod igniter: treat 5s to open, and ignite for 15 seconds as a cycle, then can ignite at least 5000 times (around 20 years).
- Ignitor working voltage at below 132v and compatible gas furnace models: dms90453bxa, p1256701f , p1256707f , dms90703bxa, p1256702f , p1256708f , dms90704cxa, p1256703f , p1256709f , dms90904cxa, p1256704f , p1256710f , dms90905dxa, p1256705f , dms91155dxa, p1256706f , gcs90453bxa, p1257201f , p1257207f , gcs90703bxa, p1257202f , p1257208f , gcs90904cxa, p1257204f , p1...
- The hot side igniter/igniter temperature: >= 1100°c at 102v/ 17 seconds . >= 1180°c at 120 v/ 17 seconds ,>= 1400°c at 132 v/ 17 seconds .common repair replacement with hvac controls, janitrol, furnace, janitrol furnace, amana goodman etc furnace hot surface ignitor/igniter
- Replacement of goodman model 20165703s ignitor - 594468, replace of heating gms80904bnbc , gms80453ana
SHOWview product -
Product Highlights
- 🔥 [fuction] flame sensor ignitors design to monitor and verify whether a flame is burning inside the furnace. the flame sensor is a safety component of a furnace located on the interior of the burner assembly, can be universal kit if you can adjust the height of spark pin in right posistion. the two pin will increase the power during spark and higher efficiency igniting...
- 🔥 [easy to install] 62-24164-01 direct spark furnace igniter is easy install even for beginners, remove the broken sensor and replace it with our new sensor after shut off the power to your furnace. direct spark furnace igniter flame sensor sensing rod -ground electrode offset is 135 degrees, spark electrode offset is 83 degrees. the electrode pin can be bent if you nee...
- 🔥 [wide compatibility] direct spark furnace ignitors are compatible with the rheem water heaters furnace pro-tech pse r36 pser36. furnace burner igniters part number: 62-24164-01, 622416401 and 2-prong electrode assembly replacement for suburban part number is 232258, with two sparking for fireplace, fire pit, furnace etc.
- 🔥[premium quality] furnace burner igniters are made of high quality iron chromium aluminum alloy and heat-resistant materials with high temperature resistance cable which can resist around 480°f temperature during working condition.
- 🔥 [package includes] 2 pack 62-24164-01 flame sensor ignitors replacement for rheem furnace with 232258 2-prong electrode assembly and 31.5" high-temperature rubber cable wire. the round pin terminal diameter of 0.084 inches, the mounting flange to the top of the igniter of 2-1/8 inches, the ground electrode offset of 13/16 inches, the spark electrode offset of 1-3/16 i...
SHOWview product -
Product Highlights
- Diy ignition parts with double sparker and 33.5inch 480°f resistance high temperature cable
- The electrode pin can be bended if you need adjust the installation size
- Replacement of model 62-24164-01 flame sensor igniter sensing rod for rheem furnace include two sets
- Also can be used for any propane or natural igniter system like grill, fire pit and water heater if you can adjust the height of the sparking area to fit your burner
- This kit need to be worked with igniter or control system to ignition.
SHOWview product -
Product Highlights
- Graphite impregnated fiberglass - less likely to get stuck with creosote ensuring a better and more consistent seal.
- Professional strength cement - withstands 2000-degrees farenheit. adheres to all types of stoves from steel to cast iron.
- Abrasion/crush resistant - graphite impregnation/lubrication makes gasketing more abrasion resistant.
- Black gasket - used by leading stove manufacturers due to better aesthetics and higher performance.
- Made in usa - quality manufactured in the united states.
SHOWview product -
Product Highlights
- [superior quality] this direct spark igniter uses resistance heating wire and resistance wire made of ferrite iron-chromium-aluminum alloy. therefore this flame sensor ignitors is characterized by high resistivity and good oxidation resistance.
- [product specification] the direct spark igniter has the wire length of 35 inches, the round pin terminal diameter of 0.084 inches, the mounting flange to the top of the igniter of 2-1/8 inches, the ground electrode offset of 13/16 inches, the spark electrode offset of 1-3/16 inches, and the spark gap of 1/8 inch.
- [applications] this direct spark furnace igniter is compatible with the rheem pro-tech pse r36 pser36. furnace burner igniters part number: 62-24164-01, 622416401.
- [easy installation] 62-24164-01 furnace burner ignitors repalcement is easy to install. after turning off the power to the furnace, the installation is completed by removing the damaged ignitor and replacing the ignitor with one of our new flame sensor ignitors.
- [package & after sales] 2pcs x direct spark ignition ignitors. if you have any questions about flame sensor igniter sensing rod fit, you can email us and we will help you within 24 hours.
SHOWview product -
Product Highlights
- 【 3 outlet pigtail 】 multi plug extension cord comes with a pigtail triple tap; allow you to power multiple appliances simultaneously and maximize the usage of power strips and wall outlets
- 【 lighted extension cord end 】 led indicator lights up when the cord is powered to let you know the 2 foot short extension cord is ready to use and easy to be found in the dark
- 【 heavy duty 12 gauge extension cord 】 15a / 125v / 1875w; premium stw 12/3 gauge contractor grade power cable has thicker, 600-volt insulation, designed for heavier use
- 【 for indoor / outdoor 】 this power cord splitter is suitable for temperatures from -40°f to 140°f; yellow pvc jacket withstand a lifetime of wear and tear and can resist abrasion, moisture, and direct sunlight; note: make sure the connections are not immersed in water
- 【 ul listed 】 built with all-copper wire, reinforced blades, and double jacketed cords; features full-molding design; certified to ul
SHOWview product -
Product Highlights
- High temperature resistant: our fiberglass rope seal gasket can withstand the high temperature up to 550°c / 1022°f. with high insulating properties and excellent thermal stability, you can use it for wood burning stoves with confidence.
- Wide usages: the fiberglass rope seal gasket can be widely used for various chimneys, fireplaces, boilers, industrial stoves and wood burning stoves, etc. suitable for both home and industry.
- Reliable material: our fireplace tape seal is made of high quality fiberglass, sturdy, wear resistant and long-lasting, not easy to wear off. without asbestos, it is more heat resistant and flexible.
- Easy to install: firstly, measure the desired length and cut; then, remove the old seal and clean the place carefully; next, glue the new fireplace tape seal.(tips: if you want to be more solid,you can use stove cement to stick and fix it firmly. please note that package don't include stove cement.)
- Package content: you'll receive 1 flat wood stove gaskets with self-adhesive backing. (width:20mm,thickness:3mm,length:2m/78.7 inch)
SHOWview product -
-
Coupon copied
